In the field of high-end manufacturing, the surface properties of parts directly affect the performance and service life of the product, and the wear of equipment parts often causes additional time and economic cost loss. In order to improve the surface performance of mechanical parts, surface strengthening treatment is usually used to improve the surface performance and service life of the material. In addition to direct surface strengthening of the material, coating is usually prepared on the surface, such as thermal spraying on the surface of the material in metallurgy, petrochemical and other fields to improve the service life. However, due to the shortcomings of thermal spraying technology, it can not effectively improve the surface mechanical properties of materials. In addition, when special coatings are prepared by magnetron sputtering, electroplating and chemical vapor deposition, there are often shortcomings such as limited thickness and poor adhesion.
Laser cladding technology is a new metal surface treatment technology, which is often used to prepare high hardness wear-resistant coatings with strong bonding force and few defects. As a chip-free and efficient 3D forming technology, laser cladding has been successfully applied to green manufacturing and remanufacturing of some high-end engineering parts.
The principle of strengthening process
Laser cladding is on the surface of the substrate to be coated, with different feeding methods, through laser irradiation to melt a thin layer of the substrate surface at the same time, and after rapid solidification to form a very low dilution and metallurgical bonding with the substrate surface coating. The technology is characterized by high power density, high deposition efficiency, low thermal deformation, rapid cooling, low dilution rate and high metallurgical properties
In laser cladding, the laser beam is focused on a small area on the surface of the material, causing it to heat up rapidly, reaching the melting point of the material or a higher temperature. At high temperatures, the substrate forms a melt pool with the cladding material, and the atoms and molecules of the material begin to become dynamic in the melt pool and can be rearranged into different crystal structures or chemical compositions. When the laser beam moves to the next area, the previously melted area cools rapidly, forming a new organizational structure, so it is suitable for increasing the hardness of the material.
The mechanism that laser cladding technology can improve the hardness of materials includes the following aspects.
1. Grain refinement
Because the laser cladding layer is a special and transient solid chemical process, it has a high melting and solidification rate, which inhibits the growth of grains, promotes the refinement of grains, and thus improves the hardness of the coating. NbMoTaWTi high entropy alloy coating was prepared on the surface of TC4 alloy by laser cladding, and the microhardness was found to be 71.4% higher than that of the substrate. The reason is that the rapid melting and cooling in the laser cladding process leads to the grain cannot grow rapidly, thus the grain is refined, and the hardness is greatly improved.
2. Lattice distortion
The distortion of the crystal lattice increases the hardness of the material. In the process of plastic deformation of laser cladding layer, a large number of lattice defects, such as dislocation and vacancy, will be introduced to make some elements out of the equilibrium state and cause lattice distortion. After lattice distortion, it often leads to an increase in energy in the material, resulting in greater microstress, inhibiting dislocation slip, and improving the strength and hardness of the material. Because the high entropy alloy is composed of a variety of elements, the size, structure and bonding energy of each element atom are significantly different, in which the atomic size, bond type and lattice potential energy of different elements may be randomly distributed on the lattice points, resulting in serious lattice distortion of the crystal structure, so this phenomenon is more obvious in the high entropy alloy.
3. Phase transformation
The change of coating phase makes the hardness of coating increase. Laser cladding is a high-temperature processing technology that can heat the surface of the material to high temperatures in a very short time, melt it partially or completely, and form different organizational structures through rapid cooling. At this high temperature, the atoms and molecules of the material become dynamic and can be rearranged into a more stable or optimized crystal structure, causing a phase transition of the material. CoCrNiMnTix high entropy alloy laser cladding coating was prepared on Q235 steel surface. It was found that with the increase of Ti content in the coating, the coating phase changed from FCC phase to FCC+ Laves phase.
Effect of cladding material on coating
The type and proportion of powders are the key factors affecting the performance of coatings. Therefore, in the experiment, it is very important to design the formula of cladding powder reasonably. In addition, because the enhancement method of the coating is closely related to its strengthening effect, it is very important to design the powder according to the enhancement effect. Among them, the second phase strengthening, fine crystal strengthening, solid solution strengthening, microstructure optimization, amorphous and microstructure optimization are effective ways to improve the hardness and wear resistance of the coating. The effects of common additive elements on the surface properties of cladding coatings are shown in Table 1.
| Chemical element |
Effect |
|
Al |
It can refine the grain and form the oxide layer, so that the hardness, wear resistance, oxidation resistance and strength and toughness of the coating are improved. |
|
Si |
Appropriate addition can improve the hardness and wear resistance of the coating by affecting the lattice. |
|
Mn |
Appropriate addition can play a solid solution strengthening, improve the hardness of the effect. The coating morphology can be improved. |
|
Ti |
Improve coating hardness, wear resistance and high temperature resistance. |
|
C |
The hardness, strength, abrasion resistance and ductility of the high entropy alloy coating are significantly improved. |
|
B |
It can reduce grain boundary energy, refine dendrite structure and improve wear resistance of coating. |
|
Nb |
It can reduce grain boundary energy, refine dendrite structure and improve wear resistance of coating. |
|
WC |
Refine grain, improve coating hardness and wear resistance. |
|
Cr |
Improve coating hardness, oxidation resistance and corrosion resistance. |
Because the hardness of the material reflects the ability of the material to resist the material pressing into the surface, the higher the hardness, the shallower the depth of the material pressing into the surface of the material, the smaller the abrasion volume generated by cutting, that is, the smaller the wear, the higher the wear resistance. Therefore, hardness can be used to measure the wear resistance of metal materials, and when the hardness increases, its wear resistance will also increase.
